Choose an application
  C² Degrease · Sprayer and scrubber |
C² DegreaseSprayer and scrubberC2 DEGREASE™ Step–by-Step Application Instructions – C2 Degrease Before beginning, always read SDS and technical data sheet for complete instructions and safety information. Always prepare a test panel before proceeding.
Coverage Rates
DilutionDo not alter product except as specified. C² Degrease™ should be diluted with hot or cold water for all applications. Use soft water to improve performance at high dilution rates. Minimum recommended dilution is one part concentrate to four parts water. Use the recommended dilutions. Always test for highest possible dilution that gives effective results. Low-pressure Sprayer
Application C2 Degrease™ can be applied three different ways1. Sprayer & Auto-Scrubber.Apply properly diluted C2 Degrease™ with low-pressure pump sprayer. Let it dwell on surface for 3-5 minutes. Do not allow to dry. Over dwelling C2 Degrease™, run auto- scrubber with hot water, stiff bristle brushes (not pads), max-down pressure and lowest water setting for best performance. Heated water (65–80°C) may improve cleaning efficiency. Using too much water will only further dilute C2 Degrease™, lowering its performance. Do not run vacuum at this point. You want C2 Degrease™ to be worked into the surface for at least 2-3 passes with auto- scrubber. Do not allow to dry. After 2-3 passes, vacuum up residue. The floor needs to be rinsed well with clean water to ensure no residue is left behind. |
C² Degrease · Scrubber only |
C² DegreaseScrubber onlyC2 DEGREASE™ Step–by-Step Application Instructions – C2 Degrease Before beginning, always read SDS and technical data sheet for complete instructions and safety information. Always prepare a test panel before proceeding.
Coverage Rates
DilutionDo not alter product except as specified. C² Degrease™ should be diluted with hot or cold water for all applications. Use soft water to improve performance at high dilution rates. Minimum recommended dilution is one part concentrate to four parts water. Use the recommended dilutions. Always test for highest possible dilution that gives effective results. Low-pressure Sprayer
Application C2 Degrease™ can be applied three different ways2. Auto-Scrubber.Apply properly diluted C2 Degrease™ into auto-scrubber tank. Run auto-scrubber with hot water, stiff bristle brushes (not pads), max-down pressure and lowest water setting for best performance. Heated water (65–80°C) may improve cleaning efficiency. Using too much water will only further dilute C2 Degrease™, lowering its performance. Do not run vacuum at this point. You want C2 Degrease™ to be worked into the surface for minimum 3-4 passes with auto-scrubber. More passes are needed since C2 Degrease™ was not allowed to dwell prior to auto scrubbing. Do not allow to dry. After 3-4 passes, vacuum up residue. The floor needs to be rinsed well with clean water to ensure no residue is left behind. |
C² Degrease · Pressure washing |
C² DegreasePressure washingC2 DEGREASE™ Step–by-Step Application Instructions – C2 Degrease Before beginning, always read SDS and technical data sheet for complete instructions and safety information. Always prepare a test panel before proceeding.
Coverage Rates
DilutionDo not alter product except as specified. C² Degrease™ should be diluted with hot or cold water for all applications. Use soft water to improve performance at high dilution rates. Minimum recommended dilution is one part concentrate to four parts water. Use the recommended dilutions. Always test for highest possible dilution that gives effective results. Low-pressure Sprayer
Application C2 Degrease™ can be applied three different ways3. Pressure-washing.Apply properly diluted C2 Degrease™ into pressure-washer tank. Pressure washing at 25-65 atm with a water flow-rate of 20–30 liters per minute is the best pressure/water combination for rinsing porous concrete. Use a 15–45° fan spray tip. Heated water (65–80°C) may improve cleaning efficiency. Do not allow to dry. Once done, rinse floor with clean water and vacuum up residue. |