Choose an application

C² Remove · Sprayer and scrubber
C² Remove Sprayer and scrubber C2 REMOVE™ Step–by-Step Application Instructions – C2 Remove Before beginning, always read SDS and technical data sheet for complete instructions and safety information. Always prepare a test panel before proceeding. Use to remove wax, curing compounds, cure marks, low-solid sealers COVERAGE RATES Standard coverage rate for concentrated, non-diluted cleaner 7.5 – 12.5 m²/L PLEASE NOTE: Coverage rates are offered for estimating purposes only. Variations in concrete quality, porosity, job site conditions, temperature and relative humidity will affect coverage rates. DILUTION The product should be diluted with clean water, based upon its intended use: For removal of light wax buildup, dilute 1:10 parts water. For removal of heavy wax buildup, dilute 1:3 parts water. For removal of low-solids cure and seals, use product at full strength. APPLICATION C2 Remove™ can be applied two different ways: (pressure washing is not recommended) 1. Sprayer & Auto-Scrubber. Apply properly diluted C2 Remove™ with low-pressure pump sprayer. Let it dwell on surface for 5-10 minutes. Do not allow to dry. Over dwelling C2 Remove™ , run auto-scrubber with hot water, stiff bristle brushes (not pads), max-down pressure and lowest water setting for best performance. Heated water (65–80°C) may improve cleaning efficiency. Using too much water will only further dilute C2 Remove™ lowering its performance. Do not run vacuum at this point. You want C2 Remove™ to be worked in to the surface for at least 2-3 passes with auto-scrubber. Do not allow to dry. After 2-3 passes, vacuum up residue. The floor needs to be rinsed well with clean water to insure no residue is left behind. SBS · EN · C² Remove
betonokietiklis.lt

C² Remove · Sprayer and scrubber

C² Remove

Sprayer and scrubber

C2 REMOVE™

Step–by-Step Application Instructions – C2 Remove Before beginning, always read SDS and technical data sheet for complete instructions and safety information. Always prepare a test panel before proceeding.

Use to remove wax, curing compounds, cure marks, low-solid sealers

COVERAGE RATES

Standard coverage rate for concentrated, non-diluted cleaner
7.5 – 12.5 m²/L

DILUTION

The product should be diluted with clean water, based upon its intended use:

For removal of light wax buildup, dilute 1:10 parts water.
For removal of heavy wax buildup, dilute 1:3 parts water.
For removal of low-solids cure and seals, use product at full strength.

APPLICATION

C2 Remove™ can be applied two different ways: (pressure washing is not recommended)

1. Sprayer & Auto-Scrubber.

Apply properly diluted C2 Remove™ with low-pressure pump sprayer. Let it dwell on surface for 5-10 minutes. Do not allow to dry. Over dwelling C2 Remove™ , run auto-scrubber with hot water, stiff bristle brushes (not pads), max-down pressure and lowest water setting for best performance. Heated water (65–80°C) may improve cleaning efficiency. Using too much water will only further dilute C2 Remove™ lowering its performance. Do not run vacuum at this point. You want C2 Remove™ to be worked in to the surface for at least 2-3 passes with auto-scrubber. Do not allow to dry. After 2-3 passes, vacuum up residue. The floor needs to be rinsed well with clean water to insure no residue is left behind.

SBS · EN · C² Remove

C² Remove · Scrubber only
C² Remove Scrubber only C2 REMOVE™ Step–by-Step Application Instructions – C2 Remove Before beginning, always read SDS and technical data sheet for complete instructions and safety information. Always prepare a test panel before proceeding. Use to remove wax, curing compounds, cure marks, low-solid sealers COVERAGE RATES Standard coverage rate for concentrated, non-diluted cleaner 7.5 – 12.5 m²/L PLEASE NOTE: Coverage rates are offered for estimating purposes only. Variations in concrete quality, porosity, job site conditions, temperature and relative humidity will affect coverage rates. DILUTION The product should be diluted with clean water, based upon its intended use: For removal of light wax buildup, dilute 1:10 parts water. For removal of heavy wax buildup, dilute 1:3 parts water. For removal of low-solids cure and seals, use product at full strength. APPLICATION C2 Remove™ can be applied two different ways: (pressure washing is not recommended) 2. Auto-Scrubber (Only). Apply properly diluted C2 Remove™ into auto-scrubber tank. Run auto-scrubber with hot water, stiff bristle brushes (not pads), max-down pressure and lowest water setting for best performance. Heated water (65–80°C) may improve cleaning efficiency. Using too much water will only further dilute C2 Remove™ ä, lowering its performance. Do not run vacuum at this point. You want C2 Remove™ to be worked into the surface for minimum 3-4 passes with auto-scrubber. More passes are needed since C2 Remove™ was not allowed to dwell prior to auto scrubbing. Do not allow to dry. After 3- 4 passes, vacuum up residue. The floor needs to be rinsed well with clean water to ensure no residue is left behind. SBS · EN · C² Remove
betonokietiklis.lt

C² Remove · Scrubber only

C² Remove

Scrubber only

C2 REMOVE™

Use to remove wax, curing compounds, cure marks, low-solid sealers

COVERAGE RATES

Standard coverage rate for concentrated, non-diluted cleaner
7.5 – 12.5 m²/L

DILUTION

The product should be diluted with clean water, based upon its intended use:

For removal of light wax buildup, dilute 1:10 parts water.
For removal of heavy wax buildup, dilute 1:3 parts water.
For removal of low-solids cure and seals, use product at full strength.

APPLICATION

C2 Remove™ can be applied two different ways: (pressure washing is not recommended)

2. Auto-Scrubber (Only).

Apply properly diluted C2 Remove™ into auto-scrubber tank. Run auto-scrubber with hot water, stiff bristle brushes (not pads), max-down pressure and lowest water setting for best performance. Heated water (65–80°C) may improve cleaning efficiency. Using too much water will only further dilute C2 Remove™ ä, lowering its performance. Do not run vacuum at this point. You want C2 Remove™ to be worked into the surface for minimum 3-4 passes with auto-scrubber. More passes are needed since C2 Remove™ was not allowed to dwell prior to auto scrubbing. Do not allow to dry. After 3- 4 passes, vacuum up residue. The floor needs to be rinsed well with clean water to ensure no residue is left behind.

SBS · EN · C² Remove

Choose an application

C² Remove

Sprayer and scrubber

COVERAGE RATES

DILUTION

APPLICATION

1. Sprayer & Auto-Scrubber.

C² Remove

Scrubber only

COVERAGE RATES

DILUTION

APPLICATION

2. Auto-Scrubber (Only).

Quantity calculator

AI technical expert

Guidance on Crete Colors products

What the answers are based on

Choose an application

C² Remove

Sprayer and scrubber

COVERAGE RATES

DILUTION

APPLICATION

1. Sprayer & Auto-Scrubber.

C² Remove

Scrubber only

COVERAGE RATES

DILUTION

APPLICATION

2. Auto-Scrubber (Only).

Cookies and analytics